Engineering Menu > Proxxon 12v & 240v Precision Workshop Tools > 12v Hand Held Proxxon Tools
A single speed machine 20,000rpm. Phase angle control and feedback effect circuitry yield high torques, even at low speeds. Six MICROMOT collets for shanks in the range 1.0 - 1.5 - 2.0 - 2.4 - 3.0 and 3.2mm are supplied. Power consumption is 40W, max. length 220mm and weight approx. 230g. The body diameter of only 35 mm makes it easy to handle. The weight of 230g, quiet and effortless drive are due to the special motor. The ground spindle and collar bearing all contribute to the ergonomic design. The high quality steel collets ensure accurate clamping of the cutters. The size of the machine dictates a 12V drive system, use of a transformer is required. 12V MICROMOT transformers of at least 1A are recommended. * Slim, easily handled & light weight (230g) * Quick-action chuck * 20,000rpm * Special balanced, low noise DC motor * 12V MICROMOT transformers of at least 1A are recommended
The thyristor electronic speed control enables the selection of speeds from 5,000 to 20,000rpm. Phase angle control and feedback effect circuitry yield high torques, even at low speeds. Six MICROMOT collets for shanks in the range 1.0 - 1.5 - 2.0 - 2.4 - 3.0 and 3.2mm are supplied. Power consumption is 40W, max. length 220mm and weight approx. 230g.The body diameter of only 35 mm makes it easy to handle. The weight of 230g, quiet and effortless drive are due to the special motor. The ground spindle and collar bearing all contribute to the ergonomic design. The high quality steel collets ensure accurate clamping of the cutters. The size of the machine dictates a 12V drive system, use of a transformer is required. MICROMOT transformers of at least 1 A are recommended. * Slim, easily handled & light weight (230g) * Quick-action chuck * Variable speed with feedback * Special balanced, low noise DC motor * MICROMOT 12V transformers of at least 1A are recommended
Slim, easily handled and light. Quick action chuck and electronic variable speed with feedback. Special balanced, low noise DC motor. Length 220m. N.B. 12V MICROMOT mains adaptor (476059), required to operate this tool. Slim, easily handled & light weight (230g) Quick-action chuck Variable speed with feedback Special balanced, low noise DC motor Requires 12V MICROMOT mains adaptor 28706
Complete set with a 12V mains adaptor, Milling/Drilling machine MICROMOT 50/E & 34 assorted accessories.The accessories include: 1 diamond grinding bit, 1 fine miller, 0.5 and 1.0 mm micro-drills, 1 brass brush, 4 carborundum grinding bits (cylinder, sphere, disc and cone shaped), 1 saw blade, 4 grinding wheels 22 x 3 mm (2 carborundum, 2 silicon carbide), 20 cutting discs, 1 arbor. With mains adapter for 240V operation (12 Volt, 1.0A). Packed in a durable plastic case.
Ideal for curved cuts in wood (up to 10mm), corrugated boards (up to 3mm) and non-ferrous metals (up to 2.5mm). Equipped with a powerful 12 - 18 Volt five-pole motor. Power consumption 100W, max. 6mm stroke. The number of strokes may be adjusted between 2,000 and 5,000 per minute. Stable housing of fibreglass reinforced POLYAMIDE. Includes two saw blades (coarse and fine). We recommend MICROMOT mains adaptor from 2.0A for powering the jigsaw. * Powerful 5-pole motor operates * 6mm stroke * Variable speed 2,000 to 5,000/min. * Supplied with two blades 1 coarse & 1 fine. * Requires a MICROMOT adaptor of a least 2.0 A
* Precision tool for delicate or small jobs * Keyless chuck (capacity 0.3 - 3.2 mm) * Spindle lock for easy bit changing * Recessed spindle head for inserting: MlCROMOT collets * High quality 12 - 18V, 5 pole motor * Fibreglass reinforced POLYAMIDE casing * For use with MICROMOT transformers of at least 2.0A A great precision tool for delicate or small jobs which you can't do with a standard drill: e.g. precision drilling, milling, sanding, polishing, brushing, de-rusting, engraving and cutting. Includes keyless chuck (capacity 0.3 - 3.2 mm). A precision ball bearing minimises spindle side play. Spindle lock button for bit changing obviates the need for spanners. Recessed spindle head for inserting: MlCROMOT steel collets. Efficient forced ventilation cooling of motor (and electronic components in "E" model). High quality 12 - 18 Volt, 5 pole motor with variable speed 3,000 to 15,000rpm. Fibreglass reinforced POLYAMIDE casing. For use with MICROMOT transformers of at least 2.0A.
This micro screwdriver from Proxxon is light and easy to handle, and the well positioned rocker switch provides on/off/reverse. The quality ROHM three jaw chuck accepts bit shanks of up to 6.5mm. The torque range is in six stages from 0.35-2.0 Nm. Supplied complete with the following 16 insert bits of chrome molybdenum steel. Slot: 0.3 x 1.5 / 0.35 x 2.0 / 0.4x 2.5mm. Philips: sizes 0 and 1 Torx: T6, T8, and T10. Hex key internal: 3.0 / 3.5 / 4.0 / 4.5 / 5.0mm. External: 1.5 / 2.0 / and 5.0mm.N.B. This unit can also be used for small thread cutting with suitable taps.We recommend the use of a MICROMOT mains adaptor of at least 2.0A.
Load capacity 300 - 600g. Cord length up to 180cm. Housed in a sheet steel case with plastic outer cover. Weight 400g. Ideal for assembly lines & work benches.
Supplied with a tester glass so you can start engraving immediately. GG 12 engraving tool, 12 - 18V, 20,000 rpm spindle speed, fitted with ball bearing. TUV approved mains adapter (12 V, 0.5 A), motifs and instruction booklet. Bits 1.0 & 1.8mm diamond grinding bits with spherical head for engraving & line work. Silicon carbide grinding bits in both conical and bullet shape for frosting glass as well as carborundum grinding bits in ball and cylinder shape for grinding and engraving.
Heating time approx. 10 seconds On/off switch, lockable in the "on" position PTC technology ensures exact tip temperature of 310°C Light for illuminating working area Complete with spiral cable and standard MICROMOT jack plug Requires <</strong> Heating time approx. 10 seconds, with ready access to on/off switch, lockable in the "on" position. PTC technology ensures exact tip temperature of 310°C, preventing damage to sensitive electronic components such as transistors and ICs, while minimising the possibility of generating noxious gases from the solder/flux. Light for illuminating working area. Complete with spiral cable and standard Micromot Jack plug. Requires Proxxon Micromot Mains Adaptor.
The PS 13 Pensander from Proxxon is a great tool for the model maker and miniaturist. It is ideal for working on surfaces in recesses, slots and other awkward to get at areas. The durable special DC motor is housed in a glass fibre reinforced polyamide casing and the unit features a sanding stroke with a linear action, not rotational. Supplied with four sanding arbors with straight shanks and four angled (all different shapes) as well as three sheets of pre-profiled self adhesive sanding pads. The sheets are of grits 180, 240 and 400 with 5 of each shape per sheet.N.B. A mains adaptor of at least 1.0A at 10-18VDC is required. We recommend Proxxon power supplies NG2/E or NG5/E.
Three Sheets each with 20 pads in different shapes. Silicon Carbide , Self Adhesive
Super fine flame shape. Rechargeable with standard lighter fuel. Used for soldering, de-soldering or brazing etc. Ideal for model building, electronics, jewellery repairs, dental laboratories, Tiffany. Independent air and fuel adjustments. Super fine flame shape with temperature attaining Fitted with piezo lighter 120 min run time on a full charge. Includes removable stand Super fine flame shape. Rechargeable with standard lighter fuel. Used for soldering, de-soldering, brazing or heating of workpieces. Ideal for model building, electronics, jewellery repairs, dental laboratories, Tiffany. Independent air and fuel adjustments. Super fine flame shape with temperature attaining 1,300°C, using butane cartridge, rechargeable with standard lighter fuel. Fitted with piezo lighter and 500ml cartridge yielding typical usage of 120 minutes. Includes removable foot which ensures stability on the worktop.
