Soba Rotary Tables and accessories

SOBA 4" Rotary Table HV4 Type  (Ref: SHHV4)

These tables have a totally ground finish which provides high precision and smooth rotation - everything you would expect from Shobha. The centre of the table is fitted to an inner conical Morse tapered sleeve MT2.
The worm gear ratio is 90:1 i.e. one revolution of the hand wheel = 4' of rotation of the table and the vernier scale is calibrated to 10 sec.
The hardened and ground worm gear incorporate a quick release system for manual indexing.. Table diameter - 110 mm - Table height - 80 mm - Centre height - 80mm - Centre sleeve - 2MT.3 T slots

£92.14

£110.57

Soba Rotary Table HV6 150mm  (Ref: 110242)

Spec as above - This is the Soba HV6 Rotary Table only- accessories can be added later

£99.00

£118.80

SHOBA 6" ROTARY TABLE & DIVIDING PLATES  (Ref: 110242T)

AS ABOVE BUT WITHOUT THE TAILSTOCK
REMEMBER OUR PRICE INCLUDES VAT & CARRIAGE UK MAINLAND!!

£111.10

£133.32

SOBA 6" ROTARY TABLE SET C/W PLATES , TAILSTOCK etc-  (Ref: 110242S)

FANTASTIC OFFER- PRICE INCLUDES THE ROTARY TABLE , SET OF 3 DIV PLATES TAILSTOCK, AND A CLAMPING KIT
They have a totally ground finish which provides high precision and smooth rotation - The centre of the table is fitted to an inner conical Morse tapered MT2 sleeve.
The worm gear ratio is 90:1 i.e. one revolution of the hand wheel = 4' of rotation of the table and the vernier scale is calibrated to 10 sec.
The hardened and ground worm gear incorporate a quick release system for manual indexing. . Table diameter - 150 mm - Table height - 80 mm - Centre height - 105mm - Centre sleeve - 2MT.4 T slots. OUR TABLE IS SUPPLIED WITH AN 8 PAGE FULL MANUAL - NOT AVAILABLE FROM OTHER SUPPLIERS!

£145.66

£174.79

Chuck Adaptor for Four Slot 6" Rotary Tables with Boxford Thread  (Ref: 112191)

New- These are new in and allow you to easily mount a Boxford ( 1 1/2 x 8 TPI) threaded chuck to your 6" /150mm 4 slot Rotary Table
Plate is 125 mm diameter and 10mm thick

4 mounting lugs - 8 mm wide
Four T nuts and studs are included
T nust are 10mm wide at the top and 16 mm wide at the bottom
CLICK THE IMAGE TO SEE THE PLATE MOUNTED ON A ROTARY TABLE

£26.06

£31.27

DP1 Dividing Plate Set for HV4 & HV6 Type Tables  (Ref: DP1)

Suits both Soba & Vertex Type Systems
This excellent dividing attachment can easily be fitted to the HV6 rotary table and includes three plates as follows.
A Plate - 15,16,17,18,19,20
B Plate - 21,23,27,29,31,33
C Plate - 37,39,41,43,47,49
Also included are all necessary screws,washers & handle etc. to fit.

£38.31

£45.97

Chuck Adaptor for Four Slot 6" Rotary Tables with Myford Thread- SORRY- OUT OF STOCK !  (Ref: 112190)

New- These are new in and allow you to easily mount a Myford threaded chuck to your 6" /150mm 4 slot Rotary Table
Plate is 125 mm diameter and 10mm thick

4 mounting lugs - 8 mm wide
Four T nuts and studs are included
T nust are 10mm wide at the top and 16 mm wide at the bottom
CLICK THE IMAGE TO SEE THE PLATE MOUNTED ON A ROTARY TABLE

£26.06

£31.27

Tailstock for HV4 & HV6" Rotary Tables  (Ref: 111301)

Suits both the HV4 and HV6 Type tables.
The height can be varied when working with different index centres. while the angle of inclination can be changed for various machining applications. In addition the tip of the centre is finely rotatable

£44.62

£53.54

Set 6 Tnuts for HV4 & 6 Rotary Table  (Ref: TNTHV6...)

Clamp Set for HV4 & HV6" Rotary Tables  (Ref: SCK1)

This set is suitable for both the Vertex and Soba 6" Rotary tables. The set comprises 4 x Tnuts with matching 3" studs and nuts. 2 x 2" stepped clamps and 2 x 1 3/4 slotted step clamps!
Exclusive to Chronos!

£13.66

£16.39

SOBA 8" 200MM ROTARY TABLE SORRY OUT OF STOCK  (Ref: 110243)

These tables have a totally ground finish which provides high precision and smooth rotation - . The centre of the table is 3 MT
The worm gear ratio is 90:1 i.e. one revolution of the hand wheel = 4' of rotation of the table and the vernier scale is calibrated to 10 sec.
The hardened and ground worm gear incorporate a quick release system for manual indexing. Each rotary table is issued with an informative instruction manual. Table diameter - 200 mm - Table height - 105 mm - Centre height - 135mm - Centre - 3MT.4 T slots

£175.50

£210.60

SOBA 8" 200MM ROTARY TABLE SET WITH TAILSTOCK& PLATES  (Ref: 110243S)

As above but a complete set including the tailstock, Dividing set and clamping kit!

£247.50

£297.00

Dividing Set for HV8 Rotary Table-  (Ref: 110265)

Similar to above but with two plates as follows:
A Plate - 26,28,30,32,34,37,39,41,43,44,46,47,49,51,53,57,59
B Plate - 61,63,67,69,71,73,77,79,81,83,87,89,81,93,97,99

£44.07

£52.88

Tailstock for HV8 Rotary Tables  (Ref: 110247)

Suits the HV8 Type Rotary Tables.
Fully adjustable for centre height

£47.52

£57.02

Clamping Set for HV8 Rotary Tables  (Ref: 120620)

New Style 100mm Soba Rotary Table!  (Ref: 111310)

Brand new design and exclusive to Chronos!
Table Dia - 100mm
Centre- 2 Morse Taper
Overall Height when Horizontal- 55mm
Centre Height When Vertical - 75mm
This unit come complete with T nuts , step Clamps and studs to hold work to the Table
The hand wheel can be disengaged also
INTRODUCTORY OFFER WHILE STOCKS LAST

£55.84

£67.01

ROT1 - 4" Rotary Table - SORRY OUT OF STOCK !  (Ref: MX60...)

Overall height of table under 2" - a useful feature if it is to be used with smaller milling attachments. The table can be locked in any position. Centre height in vertical position 2 1/16 in bringing the table within the range of most model engineering lathes & mills. The hand wheel scale which can be zeroed, is marked in degrees and 10 min divisions. The table is calibrated in 5 deg increments around the rim. Bronze worm wheel and steel worm with 36 to 1 ratio. Gear meshing is adjustable to take up wear. A set of suitable T nuts, studs and clamps is now available (optional - shown on picture)

£52.20

£62.64

ROT1 - 4" Rotary Table With Myford Threaded Chuck Adaptor - SORRY OUT OF STOCK !  (Ref: ROT1112185)

PRICE REDUCTION !
AS ABOVE BUT COMPLETE WITH OUR MYFORD THREADED CHUCK ADAPTOR AND MOUNTING KIT !
Overall height of table under 2" - a useful feature if it is to be used with smaller milling attachments. The table can be locked in any position. Centre height in vertical position 2 1/16 in bringing the table within the range of most model engineering lathes & mills. The hand wheel scale which can be zeroed, is marked in degrees and 10 min divisions. The table is calibrated in 5 deg increments around the rim. Bronze worm wheel and steel worm with 36 to 1 ratio. Gear meshing is adjustable to take up wear. A set of suitable T nuts, studs and clamps is now available (optional - shown on picture)

£65.57

£78.68

ROT1 - 4" Rotary Table With 65 MM 3 Jaw Chuck - SORRY OUT OF STOCK !  (Ref: ROT4J3)

As above but with a 65 mm 3 Jaw Slim Body Chuck , adaptor plate and mounting kit!

PRICE REDUCTION !

Overall height of table under 2" - a useful feature if it is to be used with smaller milling attachments. The table can be locked in any position. Centre height in vertical position 2 1/16 in bringing the table within the range of most model engineering lathes & mills. The hand wheel scale which can be zeroed, is marked in degrees and 10 min divisions. The table is calibrated in 5 deg increments around the rim. Bronze worm wheel and steel worm with 36 to 1 ratio. Gear meshing is adjustable to take up wear. A set of suitable T nuts, studs and clamps is now available (optional - shown on picture).

£90.16

£108.19

ROT1 - 4" Rotary Table With 70 MM 4 Jaw Chuck - SORRY OUT OF STOCK !  (Ref: ROT4J4)

As above but with a 70 mm 4 Jaw Independent Chuck , adaptor plate and mounting kit!

PRICE REDUCTION !

Overall height of table under 2" - a useful feature if it is to be used with smaller milling attachments. The table can be locked in any position. Centre height in vertical position 2 1/16 in bringing the table within the range of most model engineering lathes & mills. The hand wheel scale which can be zeroed, is marked in degrees and 10 min divisions. The table is calibrated in 5 deg increments around the rim. Bronze worm wheel and steel worm with 36 to 1 ratio. Gear meshing is adjustable to take up wear. A set of suitable T nuts, studs and clamps is now available (optional - shown on picture)

£90.16

£108.19

Universal Adjustable Tailstock for 100mm / 4" Rotary Tables  (Ref: 111304)

New from Soba
This adjustable tailstock is suitable for all the Soba & Vertex 4"/100 mm Rotary Tables
Fully Adjustable from 2 1/4" - 3 1/2 "

£32.78

£39.34

Set T Nuts etc for ROT1 4" Rotary Table  (Ref: MX63.)

Suits the above Rotary Table

£13.60

£16.32

MILLING DVD- Mini Machines 202 - THE ROTARY TABLE - CURVES AHEAD!  (Ref: RTD202)

THIS IS A 2 DVD BOXED SET
BRAND NEW TITLE AND INCLUDES "SPIN BUDDY! SOFTWARE LICENCE
Rotary tables enable us to cut circles, curves, arcs and more, as well as precision repetitive operations, such as bolt circles, gear/sprocket teeth, scale engraving and others. We'll show you how to set up, calculate and use your mini rotary table

Introdution and Safety

- Quick review of pertinent points

Setting Up the Rotary Table

- Clamping, rough and final indicating in

Varying Degrees of Degrees

- Decimal Degrees to Degrees, Minutes and Seconds, and back again

Dialing Degrees, Minutes and Seconds

- Reading and using the DMS Vernier Scale

Dividing Plate Setup

- Installing and removing the Dividing plate setup

Dividing Plate Calculations

- Determining the correct plate and sector holes for our operations

Bed Plate Basics

- Increasing the utility of our mini rotary tables

Going Horizontal

- Using the rotary table horizontally, the tailstock, accessories and the Quick Indexer Fixture

Laying out and Visualizing Offsets

- Setting Table offsets to simplify advanced operations

Installing and Using the SpinBuddy Software

- Instantly calculate all your operations

When you purchase this volume you also purchase a Single-User license to our "SpinBuddy" software application included on the DVD disks. This program will instantly work out all the various steps for Degree, Minute and Second operations, as well as instantly find compatible Dividing plate sizes and work out sector hole calculations.
Running time 1 hr. 15 mins. approximately
RELATED BOOK WPS37 DIVIDING - SEE BELOW !!

£29.36

£35.23

New Tailstock for 4" Table above  (Ref: XC163)

SPECIAL OFFER!!
New and exclusive to Chronos - Tailstock to suit the above rotary table

£31.88

£38.26

New 80mm 3 Jaw Chuck on Mounting Plate for Soba 4" Rotary Table SORRY OUT OF STOCK  (Ref: XC763)

New- by popular demand. This is a good quality 80mm 3 Jaw chuck on a specially made backplate to suit the 4" Soba Rotary Tables. It includes inside & outside jaws as well as keys .
Exclusive to Chronos

£54.89

£65.87

65 MM 3 Jaw Chuck on Backplate for 3 & 4" Rotary Tables  (Ref: 145012)

This comprises a good quality 65 mm dia Slim Body 3 jaw chuck with reversible jaws and adjusting bars mounted on a slotted backplate. This will fit any 3 or 4" rotary table with 4 slots. The chuck mounting is standard Unimat Thread M14 x 1
CLICK THE IMAGE TO SEE THIS UNIT MOUNTED ON A 4" ROTARY TABLE

£41.36

£49.63

70 MM 4 Jaw Independent Chuck on Backplate for 3 & 4" Rotary Tables  (Ref: 146015)

This comprises a good quality 70 mm dia 4 jaw chuck and key mounted on a slotted backplate. This will fit any 3 or 4" rotary table with 4 slots. The chuck mounting is standard Unimat Thread M14 x 1
CLICK THE IMAGE TO SEE THIS UNIT MOUNTED ON A 3" ROTARY TABLE

£41.36

£49.63

New 4 Jaw Chuck on Mounting Plate for 4" Table  (Ref: V0)

This new product is an excellent accessory for any of the 4" four slot Soba Rotary Tables.
It is a good quality 4 Jaw independent chuck mounted on a specially made plate with 4 slots to allow easy fitment to the table. Chuck Diameter is 80mm and the chuck body is 30mm deep.
Exclusive to Chronos

£45.49

£54.59

4" Tilting Rotary Table  (Ref: XP3)

Excellent 4" table within the range of most model engineering lathes & mills. The hand wheel scale which can be zeroed, is marked in degrees and 10 min divisions. The table is calibrated in 5 deg increments around the rim. Bronze worm wheel and steel worm with 36 to 1 ratio. Gear meshing is adjustable to take up wear. Complete with Tiliting Table - Adjusts to 90 degrees!!

£72.81

£87.37

New 3" Soba Tilting Rotary Table  (Ref: 111307)

This is the very latest 3"/75mm Tilting Rotary Table from Soba
Unlike inferior copies it has 4 T-slots for fixing work
Table tilts upto 90 degrees and can be used anywere in between and locked. The tilting actions is graduated
The base is 100 x 95 mm with 2 x 10mm mounting holes which are 80 mm apart
Overall height when not tilted is 55 mm
The table is graduated 0-360 degrees in 5 degree divisions
The handle is graduated 0-10 degrees in 5 minute divisions
SUPERB SOBA QUALITY

£61.00

£73.20

3" Rotary Table Suitable for Myford Type Milling Slides SORRY OUT OF STOCK  (Ref: ROT3B)

Overall height of table is 1 1/2" - a useful feature if it is to be used with smaller milling attachments. The table can be locked in any position. Centre height in vertical position 1 1/2 in bringing the table within the range of most model engineering lathes & mills. The hand wheel scale which can be zeroed, is marked in degrees and 10 min divisions. The table is calibrated in 5 deg increments around the rim. Bronze worm wheel and steel worm with 36 to 1 ratio. Gear meshing is adjustable to take up wear. EXCLUSIVE TO CHRONOS

£50.04

£60.05

3" Rotary Table With Myford Threaded Chuck Adaptor SORRY OUT OF STOCK  (Ref: ROT3B112185)

AS ABOVE BUT COMPLETE WITH A MYFORD THREADED CHUCK ADAPTOR AND MOUNTING KIT

Overall height of table is 1 1/2" - a useful feature if it is to be used with smaller milling attachments. The table can be locked in any position. Centre height in vertical position 1 1/2 in bringing the table within the range of most model engineering lathes & mills. The hand wheel scale which can be zeroed, is marked in degrees and 10 min divisions. The table is calibrated in 5 deg increments around the rim. Bronze worm wheel and steel worm with 36 to 1 ratio. Gear meshing is adjustable to take up wear. EXCLUSIVE TO CHRONOS - LIMITED QTY AVAILABLE - BE QUICK

£59.15

£70.98

3" Rotary Table With 65 mm 3 Jaw Chuck  (Ref: ROT33J)

AS ABOVE BUT COMPLETE WITH A 65 MM 3 JAW CHUCK AND MOUNTING KIT

Overall height of table is 1 1/2" - a useful feature if it is to be used with smaller milling attachments. The table can be locked in any position. Centre height in vertical position 1 1/2 in bringing the table within the range of most model engineering lathes & mills. The hand wheel scale which can be zeroed, is marked in degrees and 10 min divisions. The table is calibrated in 5 deg increments around the rim. Bronze worm wheel and steel worm with 36 to 1 ratio. Gear meshing is adjustable to take up wear. EXCLUSIVE TO CHRONOS - LIMITED QTY AVAILABLE - BE QUICK

£85.56

£102.67

3" Rotary Table With 70 mm 4 Jaw Chuck  (Ref: ROT34J)

AS ABOVE BUT COMPLETE WITH A 70MM 4 JAW INDEPENDENT CHUCK AND MOUNTING KIT

Overall height of table is 1 1/2" - a useful feature if it is to be used with smaller milling attachments. The table can be locked in any position. Centre height in vertical position 1 1/2 in bringing the table within the range of most model engineering lathes & mills. The hand wheel scale which can be zeroed, is marked in degrees and 10 min divisions. The table is calibrated in 5 deg increments around the rim. Bronze worm wheel and steel worm with 36 to 1 ratio. Gear meshing is adjustable to take up wear. EXCLUSIVE TO CHRONOS - LIMITED QTY AVAILABLE - BE QUICK

£85.56

£102.67

3" Rotary Table With Milling Slide  (Ref: ROT3VMS)

3" Rotary Table Plus Milling Slide Suitable for Myford ML7 Lathe Etc

Overall height of table is 1 1/2" - a useful feature if it is to be used with smaller milling attachments. The table can be locked in any position. Centre height in vertical position 1 1/2 in bringing the table within the range of most model engineering lathes & mills. The hand wheel scale which can be zeroed, is marked in degrees and 10 min divisions. The table is calibrated in 5 deg increments around the rim. Bronze worm wheel and steel worm with 36 to 1 ratio. Gear meshing is adjustable to take up wear.
Milling Slide
Table size 4" x 5"
Table Travel - 80mm
EXCLUSIVE TO CHRONOS - LIMITED QTY AVAILABLE - BE QUICK

£123.00

£147.60

3" Rotary Table With Double Swivel Milling Slide  (Ref: ROT3SVMS)

3" Rotary Table Plus Double Swivel Milling Slide Suitable for Myford ML7 Lathe Etc

Overall height of table is 1 1/2" - a useful feature if it is to be used with smaller milling attachments. The table can be locked in any position. Centre height in vertical position 1 1/2 in bringing the table within the range of most model engineering lathes & mills. The hand wheel scale which can be zeroed, is marked in degrees and 10 min divisions. The table is calibrated in 5 deg increments around the rim. Bronze worm wheel and steel worm with 36 to 1 ratio. Gear meshing is adjustable to take up wear.

Milling Slide
Table size 4" x 5"
Table Travel - 80mm

EXCLUSIVE TO CHRONOS - LIMITED QTY AVAILABLE - BE QUICK
CLICK THE IMAGE FOR A LARGER PICTURE

£136.55

£163.86

New 4 Jaw Chuck on Mounting Plate for 3" Table  (Ref: V3100)

This new product is an excellent accessory for any of the 3" four slot Soba Rotary Tables.
It is a good quality 4 Jaw independent chuck mounted on a specially made plate with 4 slots to allow easy fitment to the table. Chuck Diameter is 70mm and the chuck body is 20mm deep. Clamping set is included!
Exclusive to Chronos
PIC SHOWS IT MOUNTED ON THE TABLE - TABLE NOT INCLUDED!!
CLICK THE IMAGE FOR A LARGER PICTURE

£36.38

£43.66

3" Rotary Table Adaptor with Myford Thread  (Ref: 112185)

New! This handy mounting plate allows you to mout your Myford Threaded Chucks on any surface including 3 & 4" Rotary Tables with four slots
COMPLETE WITH MOUNTING KIT

Thread is standard Myford 1 1/8 x 12 TPI. CLICK THE IMAGE TO SEE THIS ITEM MOUNTED ON A SOBA 3" ROTARY TABLE

£12.74

£15.29

Adaptor with M14 x 1 Unimat Thread  (Ref: 14503)

New! This handy mounting plate allows you to mout you rUnimat Threaded Chucks on any surface including 3 & 4" Rotary Tables with four slots
COMPLETE WITH MOUNTING KIT

Thread is standard Unimat M14 x 1. CLICK THE IMAGE TO SEE THIS ITEM MOUNTED ON A SOBA 3" ROTARY TABLE

£12.74

£15.29